Respironics Hand Held Pulse Oximeter
Respironics Hand Held Pulse Oximeter

Respironics Hand Held Pulse Oximeter

Brand/Manufacturer: RESPIRONICS
Authorized Retailer Badge
  • FSA Approved

Respironics Hand Held Pulse Oximeter is small, lightweight and easy to use hand-held unit which delivers on-the-spot oximetry readings, perfect for home use. It has visual alarms for tracking patient status. It typically operates for 100 hours continuously between battery replacements. It displays numerical values for oxygen saturation and pulse rate.


  • Respironics Hand Held Pulse Oximeter includes:
    - Hand Held Pulse Oximeter
    - Instruction and Service Manual
    - 6 AA batteries
    - Model 936 Sensor (Adult Articulated Finger Clip)
  • Stores up to 18 hours of trend memory
  • Requires no routine calibration or maintenance
  • Used for monitoring oxygen saturation and pulse rate for adult, pediatric and neonatal patients in hospital, ambulatory, home and EMS environments
  • Determines arterial oxyhemoglobin saturation (%SpO2) by measuring the absorption of red and infrared light passed through tissue
  • Oxygen saturation and pulse rate are displayed on light emitting diode (LED) digital displays
  • On each detected pulse, the perfusion LED flashes

More Information

  • Patient perfusion signals are graded as good, marginal or inadequate and are indicated as such by the LED flashing green, yellow or red. This simple method gives the user a pulse-by-pulse visual indication of waveform signal quality without requiring the user to perform complex waveform analysis during critical patient care situations
  • Sensor disconnect or malfunction is indicated by lack of good perfusion flashes and/or a dash to the left of the SpO2 value on the LED display
  • SpO2 and Pulse Rate numerical values will be replaced by dashes if adequate perfusion pulses are not received
  • When the batteries are low, the digital displays will blink
  • No patient alarms, user must frequently observe the SpO2 and Pulse Rate displays




Oxygen Saturation Range (SpO2)

0 to 100%

Pulse Rate Range

18 to 300 Pulses Per Minute


Patient Indicator: Perfusion LED
Digital Displays: 3-digit 7-segment LEDs

Measurement Wavelengths

Red: 660 nanometers
Infrared: 910 nanometers

Accuracy- SpO2 (± 1 Standard Deviation)

For adults using Finger Clip Sensors:
70 to 100% ± 2 digits
For adults using Flex, Flexi-Form or Reflectance Sensors:
70 to 100% ± 3 digits
Using Ear Clip Sensors:
70 to 100% ± 4 digits
For neonates using infant or neonatal sensors:
70 to 95% ± 3 digits

Accuracy-Pulse Rate

± 3% ± 1 digit


Operating: -20 to +50°C
Non-operating: -30 to +50°C


Operating: 10 to 90% non-condensing
Non-operating: 10 to 95% non-condensing

Power Requirements

6 AA alkaline batteries
Maximum Display Brightness: 100 hours typical operation
Minimum Display Brightness: 200 hours typical operation

Patient Isolation

 >12 M

Leakage Current

Not applicable


3"W x 6"H x 1"D (8cm x 15cm x 2cm) 


10oz (280g) with batteries


3 years warranty

Customer Reviews

Questions & Answers

question image
How do I turn on?
Pam - 4/1/2016 2:49:20 PM
answer image
Turn on the 920M PLUS by pressing and releasing the On/Standby switch. Turn off the unit by pressing and holding this switch for about 2 seconds.
Customer Care - 4/2/2016 12:48:49 AM
Please enter your and your friends email address below.
Fields marked with * are compulsory

Submit Cancel
The selected product information has been successfully emailed to your friend.

Thank you for using